SETAFLASH SERIES 3 CLOSED CUP TESTER

Re-connect the silicone tubing to the brass insert. Series 3 in the cosmetics industry See Komatsu use the Series 3 See detailed specifications Available accessories Request a quotation Download a brochure pdf More products in this subcategory. It can be determined if a sample has a flash point above or below the test temperature by detecting whether a flash has occurred or not. Initially the dry ice will evaporate almost immediately and cause considerable foaming at the surface. When pressed and held down, the control knob may be rotated to either select the mode of operation, or set the time interval for the test. The serial number and software version must be quoted in any technical query, or when ordering accessories and spare parts.

If there is not sufficient adjustment, centralise the Control Valve, and adjust the Castellated Inner Wheel, then re-adjust the Control Valve. Determination of flash no-flash and flash point. The manual flash test is carried out by pulling a lever which opens a shutter on the lid and dips the flame from the test jet through the shutter aperture into the vapour space above the sample. A number of Flash Point tests to verify operation are carried out before despatch. Yes 15 How do I know when the gas canister needs refilling? Inadequate packing may cause returned instruments to be damaged in transit, resulting in additional cost and time to rectify. On Closed Cup models, a shutter in the lid is opened and a test flame is dipped into the vapour space above the sample. Series 3 in the cosmetics industry See Komatsu use the Series 3.

Each unit is tested for electrical safety is then calibrated. Issue K 10 Jun 8 Pubn No: To extract and collect hot sample from the cup.

Series 3 in the cosmetics industry See Komatsu use the Series 3 See detailed specifications Available accessories Request a quotation Download a brochure pdf More products in this subcategory. A manual reset button is situated on the rear panel to restore power after the assembly has cooled to a safe temperature. When momentarily pressed then released, the flash detector probe is reset ready for the next test.

  MORGAN LLYWELYN ARCANA SERIES

Setaflash Series 3 Flash Point Tester

A sequence of tests at different temperatures can be used to determine the flash point of the sample. When the test flame size cannot be set correctly or there is no liquid visible in the transparent part of the gas canister 16 How many tests can I do with a full gas canister? Check that the lid is flat and that the hinge is not strained. Series 3 in the cosmetics industry See Komatsu use the Series 3. Inadequate packing may cause returned instruments to be damaged in transit, resulting in additional cost and time to rectify.

Otherwise repeat the calibration procedure.

Elcometer 6910/1 Setaflash ‘Series 3’ Closed Cup Tester

Do NOT use Auto mode. However Stanhope-Seta cannot accept teser for any omissions or errors. On Closed Cup models, a shutter in the lid is opened and a test flame is dipped into the vapour space above the sample.

This may result in some discolouration of the sample cup and surrounding area. X C 59 seconds …. Clean the shutter with a suitable solvent.

Turn the canister the correct way round brass insert uppermost and re-insert it into the holder. Integral timer for standard 1 srtaflash 2 minute tests, setfalash up to 30 minutes Audible and visual indication Temperature measurement: Methods of test for paints. A “popping” sound may be heard when the flame is dipped into the vapour space. Yes, it is advisable if there are likely to be any hazardous fumes, but the fume cupboard should be free of excessive draughts 8 How can I accelerate cooling of the cup between tests?

Setaflash Small Scale Closed Cup Flashpoint Tester

To use the cooling block, carry out the following steps: REPAIR 1 If the instrument is to be returned to our factory for repair, ensure that it is adequately packed for the intended method of transport.

  MAGALUF WEEKENDER EPISODE 3 ITV PLAYER

Release Rotate the Control Eeries …. Remove all traces of the solvent 7 Should I use this equipment in a fume cupboard? Yes, it is recommended when the equipment is not being used for an extended period 14 Is the instrument made of flame-retardant materials?

Rapid equilibrium closed cup method IP Methods of test for paints. Rapid equilibrium closed cup method.

Lightly smear it with light oil and close the lid. Re-connect the silicone tubing to the brass insert. Yes 15 How do I know when the gas canister needs refilling?

Stanhope Seta™ Setaflash™ Series 3 Closed Cup Flash Point Tester Flash Point Testers

The procedure is carried out via the panel controls and requires a reference thermometer and some thermo-conductive paste. To access the fuse, prise the fuse holder open with a screwdriver blade. Calibration and verification equipment available. Check also the operation of the flash detector and verify the cup temperature 4 What happens if the thermal reset button trips?

The information contained in this publication is believed to be accurate and correct at the time of printing. If the user of this publication has any comment, query or suggestion, please contact Stanhope-Seta Ltd. eeries

Automatic Sample Cup material Aluminium Operational cuo temperature range: XoC 0 seconds …. The Setaflash Series 3 Flash Point Testers are calibrated for temperature using a single point method.

The time delay between the cup reaching the set temperature and the audible prompt to carry out the manual flash test i. An Open Cup tester, Modelis also available.